Kasi 6x4 Infrared/Hotbox Trlr

This information is from the Manufacturer's website and refers to products within the Ranger Model Series.

 

 CHAMBER DIMENSIONS:

  

            4’ X 6’ X 8”

 

 

CHAMBER CONSTRUCTION:

 

          16 GAUGE WELDED STAINLESS STEEL

 

          A FRAME: STAINLESS STEEL ANGLE AND TUBING

 

          BOX FRAME: STAINLESS STEEL TUBING

 

          CHAMBER SUPPORT ARMS: STAINLESS STEEL TUBING

 

          CHAMBER CORNER SUPPORTS: STAINLESS STEEL ANGLE

                         

          LOUVERS: 18 GUAGE STAINLESS STEEL

 

 

 

36” SEAMLESS 3/8 “ WALL STAINLESS STEEL PIPE  CONVERTERS

 

AUTOMATIC LATHE MACHINED LPG VAPOR ORAFICES

 

PRECISION WELDED 16 GUAGE STAINLESS STEEL REFLECTORS

 

18 “ INCONEL INFRARED GRIDS

 

16 CONVERTERS REQUIRED IN A STANDARD 8 ROW 6’ X 8’ CHAMBER

 

 

 

 

 

 

 

TRIPLE WALL CONSTRUCTION:

 

          INNER WALL AND SHOVEL DECK:  10 GUAGE STEEL

 

          MIDDLE WALL:  14 GUAGE STEEL

 

          OUTER SKIN:  12 GUAGE STEEL

 

          INSULATION:  1 INCH INNER WALL 2 INCHES OUTER WALL

 

 

TOP DOORS:  INSULATED AND MANUALLY OPERATED

 

SHOVEL DOOR: INSULATED SLIDING DOOR

 

                                2 TON I REAR SHOVEL DOOR

 

 

 

 

 

DIRECT AIR INFRARED BURNERS WITH  PRECISION MACHINED

                                CERAMIC TILES IN PRECISION FIT BURNERS

                                TO PREVENT CERAMIC TILE CRACKING.

 

EXTERNAL VENTURI AIR SOURCE: BURNERS DRAW DIRECT OUTSIDE

                               AIR FOR CONSISTENT INTERNAL OXYGEN SUPPLY.

 

UPPER VENTS: VENTED TO THE OUTSIDE NOT THE INSIDE OF THE

                             ASPHALT COMPARTMENT.

 

BTU OUTPUT: 1 TON RE-CLAIMER ONE 50,000 BTU BURNER

                         

 

 

 3” X 5” X 3/8” WALL SEAMLESS STEEL TUBING.

 

 

 

 

 

7,000 LB  AXLES AND SOLID STEEL WHEELS. WHEELS  

 

15 CUBIC FOOT TOOL STORAGE AREA AND DECK

 

 

A SELF CONTAINED 12 VOLT SYSTEM COMPRISED OF FOUR 6 VOLT DEEP CYCLE MARINE BATTERIES MAINTAINED BY THE TRUCK CHARGING SYSTEM WITH A BUILT IN 20 AMP MARINE BATTERY CHARGER/MAINTAINERS.

 

 

PROPANE VAPOR IS SUPPLIED BY THREE 100 LB MULTI VALVE VAPOR DRAW PROPANE TANKS CONNECTED TO COMMON MANIFOLDS BY FLEXIBLE 1/2" ID HIGH PRESSURE HOSE WITH POL VALVE TANK CONNECTORS.

 

THE FUEL/AIR MIX IS DRIVEN BY A 12V BRUSHLESS MOTOR.

 

THE FLEXIBLE HIGH PRESSURE HOSE CONNECTION TO THE MIXING CHAMBERS

FOR THE BLOWER MOTOR IS ½” ID

 

ALL FIXED PROPANE LINES ARE TO BE CONTINUOUS STAINLESS

STEEL TUBING WITH SWAGELOCK FITTINGS.

 

½”DIAMETER X .035” WALL FOR THE RE-CLAIMER

 

 ¾” DIAMETER X .035 WALL FOR THE CHAMBER.

 

ONE 300,000 BTU REGULATOR AND LINES FOR THE RE-CLAIMER  

 

ONE 1.3 MILLION BTU REGULATOR FOR THE CHAMBER

 

ALL TIED BY STAINLESS STEEL TUBE AND SWAGELOCK MANIFOLDS.

 

PRESSURE OUTPUT FOR ALL REGULATORS IS SET AT 11 INCHES OF WATER

 

 

PRESSURE ACTIVATED GAS SOLENOID TO PREVENT THE FLOW OF VAPOR WHEN THE UNIT IS NOT OPERATING.

 

FULL TIME FLAME SENSING SHUT OFF CONTROLS

 

EXCESS FLOW CHECK POL VALVES

 

MASTER CUT OFF SWITCH IS LOCATED INSIDE A LOCKABLE CONTROL BOX.

 

ALL LED LIGHTING.

 

CONTINUOUS STAINLESS STEEL TUBING AND SWAGELOCK FITTINGS ON ALL

LPG SYSTEMS.

 

 

 

 

 

 

THREE ROWS OF INFRARED CONVERTERS MINIMUM.

 

HEAT TIME FOR A DEPTH OF TWO INCHES IN STANDARD MIX DESIGN ASPHALT CEMENT IS SEVEN TO TEN MINUTES AT AN AMBIENT AIR TEMPERATURE OF 50 F WITH NO DAMAGE OR CHANGE IN THE ASPHALT BINDER.

 

FUEL CONSUMPTION NOT TO EXCEED 6.8 GALLONS OF LPG PER HOUR IN CONTINUOUS OPERATION.

 

 

 

HOLDING TIME IS INDEFINITE, BUT DEPENDENT ON THE MIX.

 

RE-CLAIMING TIME IS TWELVE TO SIXTEEN HOURS DEPENDENT ON OUTSIDE TEMPERATURE

 

MAXIMUM INTERIOR SKIN TEMPERATURE IS 325 F

 

HOLDING TEMPERATURE OF MIX IS 275 F TO 300 F

 

 

 

FOUR SIX VOLT DEEP CYCLE MARINE BATTERIES CONNECTED FOR TWELVE VOLT OUTPUT.

 

ONE BUILT IN MARINE BATTERY MAINTAINER/CHARGER.

 

 

ONSITE TRAINING AVAILABLE FOR UP TO 10 PERSONS FOR ONE DAY TO COVER OPERATION, APPLICATION AND MAINTENANCE OF UNIT.