Asphalt Distributor Trucks & Trailers

Description of Tank: Our propane heated A300 is designed for the spraying of tar emulsion or coal tar based products SS1H, CRS, CRS2P. It’s perfect for a range of materials including materials that require heating up to 170F. In summer you may not need to heat the material at all as the sun will heat up the tank and the material in it. The tank is pressure sealed which dramatically extend the material life and allows the material to be reheated when needed. Tank has a double sealed lid, which can be padlocked shut.
Safety Relief Valve: At 180F the relief valve will pop off.
Pump System: The pump is an 8gpm pump and is capable of providing 8gpm at each spray nozzle when all 8-spray nozzles are activated simultaneously. Material flow can be regulated from a flow adjuster located behind the pump. The A300 HT is designed to pump out 1-2 gallon per minute and is adjustable also from 0-2gpm. You can also put a seal coat nozzle on valve and it will increase output up to 4 gallons per minute.
Heating System: The burner is lit using a trigger switch igniter. First turn burner on, then turn on the air circulator, allow 4-5 minutes forcirculation to evenly heat tank from top to bottom. The burner is a 'sealed’ burner. Think of it as a big gas pipe extending from rear of unit, across floor, to front of unit, whereby the front is ‘closed’. The blower blows hot air into the pipe, which radiates from pipe to tank. With this indirect heating design, the burner flame does not come into direct contact with the material tank.
Safety on Burner Design: The burner is sealed at the rear of the machine on the opposite side from the cleaning solution tank. This prevents the cleaning solution from contacting the flame and causing a fire. When you are ready to spray you can shut off the gas burner.
Material Circulation: An onboard 8gpm pump circulates material through the tank from the bottom of tank to upper 2/3 of tank.
Spraying & Nozzles: There is a lever to close a 3 way valve by which Forward operates the spray wand, Center is Shut Off, pull Back
operates the ground spray bar. Each nozzle on the spray bar has a gate valve and can be shut on/off individually.
Cleanout: The unit comes with an 8-gallon poly cleanout tank with gate valve. To cleanout, close gate valve at bottom front of tank
from material tank to pump, then open gate valve above it and allow cleanout material to pump into either spray hose or spray bar.
When cleaning solvent comes out clear, your system is clean. Leave cleaning material in the lines until next use
Shipping Dimensions:
A550: 157”Lx74.5”Wx90”H, 2000 LBS(with spray bar 177”L, 2250 LBS) (with Optional carrier platform add 22” to Length)
A300: 127”Lx72.5”Wx92”H, 1400 LBS (with spray bar 146”L, 1700 LBS) (with Optional carrier platform add 22” to Length)
Required Truck Size: The A300 can be towed by a small pickup truck (550HT requires ¾ ton truck)
Note: This unit does ‘not’ have automatic temperature control or agitation.

Standard Features:
·         8gpm pump
·         50' hose and hose reel
·         Spray wand with handle and on-off valve
·         30gal propane tank
·         8 gallon poly cleanout tank
·         Hitch - Choice of style (2", 2 5/16", eye, pintle)
·         DOT lights
·         Break Away Kit installed
·         Single axle on 300HT, Tandem axles on the 550HT
·         Electric brakes on all axles.
·         Wheels 15” on 300HT only, all others 16” wheels
·         Full 1 year warranty with every part you'll ever need.
·         Comes with operations manual.

A300 gallon Tack unit on trailer $7,450
Option: Fold down spray bar 6’long, 6 nozzles (max spray width 9’,minimum 17”), with platform $1,492.
Spray bars over 6’ long, up to 15’ Priced On Request
Option: Fold down spray bar 6’long, 6 nozzles – not mounted $1,192.
Option: Air Blower Carrier (extends off front tongue) (Adds 6”L) $240.

Option: Blower, Billy Goat, 13HP $1,609.

Click over image to enlarge

Description of Tank: Our propane heated A550 is designed for the spraying of tar emulsion or coal tar based products SS1H, CRS, CRS2P. It’s perfect for a range of materials including materials that require heating up to 170F. In summer you may not need to heat the material at all as the sun will heat up the tank and the material in it. The tank is pressure sealed which dramatically extend the material life and allows the material to be reheated when needed. Tank has a double sealed lid, which can be padlocked shut.
Safety Relief Valve: At 180F the relief valve will pop off.
Pump System: The pump is an 8gpm pump and is capable of providing 8gpm at each spray nozzle when all 8-spray nozzles are activated simultaneously. Material flow can be regulated from a flow adjuster located behind the pump. The A550 HT is designed to pump out 1-2 gallon per minute and is adjustable also from 0-2gpm. You can also put a seal coat nozzle on valve and it will increase output up to 4 gallons per minute.
Heating System: The burner is lit using a trigger switch igniter. First turn burner on, then turn on the air circulator, allow 4-5 minutes forcirculation to evenly heat tank from top to bottom. The burner is a 'sealed’ burner. Think of it as a big gas pipe extending from rear of unit, across floor, to front of unit, whereby the front is ‘closed’. The blower blows hot air into the pipe, which radiates from pipe to tank. With this indirect heating design, the burner flame does not come into direct contact with the material tank.
Safety on Burner Design: The burner is sealed at the rear of the machine on the opposite side from the cleaning solution tank. This prevents the cleaning solution from contacting the flame and causing a fire. When you are ready to spray you can shut off the gas burner.
Material Circulation: An onboard 8gpm pump circulates material through the tank from the bottom of tank to upper 2/3 of tank.
Spraying & Nozzles: There is a lever to close a 3 way valve by which Forward operates the spray wand, Center is Shut Off, pull Back
operates the ground spray bar. Each nozzle on the spray bar has a gate valve and can be shut on/off individually.
Cleanout: The unit comes with an 8-gallon poly cleanout tank with gate valve. To cleanout, close gate valve at bottom front of tank
from material tank to pump, then open gate valve above it and allow cleanout material to pump into either spray hose or spray bar.
When cleaning solvent comes out clear, your system is clean. Leave cleaning material in the lines until next use
Shipping Dimensions:
A550: 157”Lx74.5”Wx90”H, 2000 LBS(with spray bar 177”L, 2250 LBS) (with Optional carrier platform add 22” to Length)
A300: 127”Lx72.5”Wx92”H, 1400 LBS (with spray bar 146”L, 1700 LBS) (with Optional carrier platform add 22” to Length)
Required Truck Size: The A550 is towed using a minimum ¾ ton truck.
Note: This unit does ‘not’ have automatic temperature control or agitation.

Standard Features:
·         8gpm pump
·         50' hose and hose reel
·         Spray wand with handle and on-off valve
·         30gal propane tank
·         8 gallon poly cleanout tank
·         Hitch - Choice of style (2", 2 5/16", eye, pintle)
·         DOT lights
·         Break Away Kit installed
·         Single axle on 300HT, Tandem axles on the 550HT
·         Electric brakes on all axles.
·         Wheels 15” on 300HT only, all others 16” wheels
·         Full 1 year warranty with every part you'll ever need.
·         Comes with operations manual.

A550 gallon Tack unit on trailer $11,585.
Option: Fold down 6’ spray bar with 6 nozzles  (max spray width 9’,minimum 17”) and platform $1,492.
Option: Spray bars over 6’ long, up to 15’ Priced On Request
Option: Fold down 6’ spray bar with 6 nozzles, not mounted $1,192.
Option: Air Blower Carrier (extends off front tongue) (Adds 6”L) $240.

Option: Blower, Billy Goat, 13HP $1,609.

Click over image to enlarge

Our 600-3,000 gallon distributor trailers are built for efficient and accurate heating and or application of asphalt cement, tack coat and emulsions. Our trailer mounted units are available in 600, 800, 1000, 1200, 2000 and 3000 gallon capacities. Choose either propane or diesel heated. A simple to use curbside control panel offers switch control of the spray bar, hand wand and circulation system. Automatic temperature controls can be set to maintain a temperature from 0-550F. Our hydraulic extension spray bars allow up to 12+ feet of spraying width.

Click over image to enlarge

Our distributor trucks are built for efficient and accurate heating and application of AC, asphalt cement and emulsions on medium and large roadway and parking lot projects. Truck mounted units are available in 1000, 1800, 3000 and 4000 gallons and offer a basic or fully computer controlled pumping system. The diesel or propane heating system allows for full circulation, spray bar and hand wand pumping, with electronic thermostat temperature controls and a circulation flush system to reduce hazmat disposal fees.

Click over image to enlarge

Our slip in and hook style distributor tank systems are built for efficient and accurate heating and application of AC, asphalt cement, tack coating and high-temperature materials. These pumping spray systems are available in 600, 750, 1000, 2000 and 3000 gallon capacities. Choose either propane or diesel heat. A tether allows for full control of the sprayer from the cab or alongside. Choice of spray bar allows for spraying a width of up to 12'.

Click over image to enlarge